Switch công nghiệp quản lý Planet IGS-6329-8UP2S2X là bộ chia mạng Ethernet chuẩn công nghiệp quản lý PoE ( Industrial Managed Switch PoE), cung cấp 8 cổng 10/100/1000Mbps PoE++, 95W/port, tổng công suất 360W và 2 cổng Uplink SFP quang SFP 1000Mbps + 2 cổng Uplink quang SFP+ 10GbE.
Industrial Managed Switch PoE IGS-6329-8UP2S2X được bảo vệ với vỏ kim loại chuẩn IP30, chuyên dùng lắp đặt tại các khu vực có môi trường, thời tiết khắc nghiệt –40 to 75 độ C, như tủ kỹ thuật trên đường phố, khu công nghiệp, nhà máy sản xuất công nghiệp,.v.v. Switch công nghiệp PoE Planet IGS-6329-8UP2S2X là giải pháp networking tốc độ cao Gigabit cho các vị trí lắp đặt ngoài trời có công suất phụ tải lớn, như Camera IP P/T/Z, Wifi AP công cộng, điện thoại VoIP và truyền dữ liệu tới mạng trục cáp quang ở xa dễ dàng, tiện lợi.
Switch PoE quản lý chuẩn công nghiệp IGS-6329-8UP2S2X giúp các quản trị viên có thể cấu hình, giám sát QoS tại chỗ hoặc từ xa qua giao diện Web/SMNP tiện dụng cho các mạng Ethernet cho trong các doanh nghiệp lớn.
Mục lục:
Các tính năng nổi bật Switch công nghiệp quản lý Planet IGS-6329-8UP2S2X:
- 8 port Gigabit 10/100/1000Mbps, giao diện RJ45, tổng công suất 360W. Hỗ trợ PoE++ IEEEaf/at/bt 95W/port
- 2 cổng quang SFP 1000Mbps + 2 cổng quang SFP+ 10GbE
- Hỗ trợ VLAN, Spanning Tree Protocol, Link Aggregation, Network Security function.
- Switch công nghiệp quản lý (Managed Switch) Layer 3.
- Hỗ trợ cấu hình, giám sát QoS tại chỗ hoặc từ xa qua giao diện Web/SMNP.
- Môi trường hoạt động –40 to 75 degrees C, chuẩn vỏ bảo vệ IP30.
- Nguồn điện: 37~56V DC
Thông số kỹ thuật Switch công nghiệp Planet IGS-6329-8UP2S2X
Hardware Specifications | |
---|---|
Copper Ports | 8 10/100/1000BASE-T RJ45 auto-MDI/MDI-X ports |
SFP Ports | 2 1000BASE-SX/LX/BX SFP slot interfaces (Port-9 and Port-10) Compatible with 100BASE-FX and 2500BASE-X SFP |
SFP+ Ports | 2 10GBASE-SR/LR SFP+ slot interfaces (Port-11 to Port-12) Compatible with 1000BASE-X and 2500BASE-X SFP |
PoE Injector Ports | 8 ports with 802.3bt PoE++ injector function with Port-1 to Port-8 |
Console | 1 x RJ45-to-RS232 serial port (115200, 8, N, 1) |
Reset Button | < 5 sec: System reboot > 5 sec: Factory default |
Connector | Removable 6-pin terminal block for power input Pin 1/2 for Power 1, Pin 3/4 for fault alarm, Pin 5/6 for Power 2 Removable 6-pin terminal block for DI/DO interface Pin 1/2 for DI 1 & 2, Pin 3/4 for DO 1 & 2, Pin 5/6 for GND |
Alarm | One relay output for power failure. Alarm relay current carry ability: 1A @ 24V DC |
Digital Input (DI) | 2 digital inputs: Level 0: -24~2.1V (±0.1V) Level 1: 2.1~24V (±0.1V) Input load to 24V DC, 10mA max. |
Digital Output (DO) | 2 digital outputs: Open collector to 24VDC, 100mA |
Enclosure | IP30 aluminum case |
Installation | DIN-rail or wall mounting |
Dimensions (W x D x H) | 76 x 135 x 152 mm |
Weight | 1,152g |
Power Requirements | Dual DC 48~54V, 8A max. (>52V DC for 802.3bt PoE++ output recommended) |
Power Consumption | Max. 29 watts/[email protected] DC input (System on) Max. 401 watts/1,[email protected] DC input (Full loading with 802.3bt PoE++ function) |
ESD Protection | Air 8KV DC Contact 6KV DC |
Surge Protection | 4KV DC |
LED Indicator | System: Power 1 (Green), Power 2 (Green), Alarm (Red) Ring (Green), Ring Owner (Green), DIDO (Red) Per 10/100/1000T RJ45 PoE++ Port: 1000Mbps LNK/ACT (Green) 10/100Mbps LNK/ACT (Amber) 802.3bt PoE++-in-use x 1 (Green) 802.3at/af PoE-in-use x 1 (Amber) Per SFP Interface: 1G/2.5G LNK/ACT (Green) 100 LNK/ACT (Amber) Per SFP+ Port: 10Gbps LNK/ACT (Green) 1Gbps LNK/ACT (Amber) PoE Usage: 90W, 180W, 270W, 360W (Amber) |
Switching Specifications | |
Switch Architecture | Store-and-Forward |
Switch Fabric | 60Gbps/non-blocking |
Throughput (packet per second) | [email protected] 64 bytes packet |
Address Table | 32K entries, automatic source address learning and aging |
Shared Data Buffer | 32Mbits |
Jumbo Frame | 10Kbytes |
SDRAM | 512Mbytes |
Flash Memory | 64Mbytes |
Flow Control | IEEE 802.3x pause frame for full-duplex Back pressure for half-duplex |
Power Over Ethernet | |
PoE Standard | IEEE 802.3bt PoE++ Type-4 PSE Backward compatible with 802.3at PoE+ PSE |
PoE Power Supply Type | 802.3bt UPOE/POH End-span Mid-span Force |
PoE Power Output | 802.3bt PoE++ Per port 52V~54V DC (depending on the power supply), max. 90 watts UPoE(PoH) Per port 52V~54V DC (depending on the power supply), max. 95 watts IEEE 802.3at Standard Per port 52V~54V DC (depending on the power supply), max. 36 watts Force Per port 52V~54V DC (depending on the power supply), max. 60 watts |
Power Pin Assignment | End-span: 1/2(-), 3/6(+) Mid-span: 4/5(+), 7/8(-) 802.3bt/UPoE: 1/2(-), 3/6(+),4/5(+), 7/8(-) |
PoE Power Budget | Single power input: 240W maximum (depending on power input) Dual power input: 360W maximum (depending on power input) ※Dual power input must be the same as DC voltage, like dual 54V |
PoE Ability PD @ 12.5 watts | 8 units |
PoE Ability PD @ 25 watts | 8 units |
PoE Ability PD @ 51 watts | 6 units |
PoE Ability PD @ 71 watts | 4 units |
PoE Management Functions | |
Active PoE device alive detects | Yes |
PoE Power Recycle | Yes, daily or predeinded schedule |
PoE Schedule | 4 schedule profiles |
PoE Extend Mode | Yes, max. 160 to 200 meters |
PoE System Management | System PoE Admin control Total PoE power budget control Auto power input and PoE budget control PoE Legacy mode Over-temperature threshold alarm PoE usage threshold alarm |
PoE Port Management | Port Enable/Disable/Schedule PoE mode control 802.3bt UPoE 802.3at End-span 802.3at Mid-span Force mode Port Priority |
Layer 2 Functions | |
Port Configuration | Port disable/enable Auto-negotiation 10/100/1000Mbps full and half duplex mode selection Flow control disable/enable Port link capability control |
Port Status | Display each port’s speed duplex mode, link status, flow control status, auto negotiation status, trunk status |
Port Mirroring | TX/RX/both Many-to-1 monitor Supports up to 5 sessions |
VLAN | IEEE 802.1Q tagged VLAN IEEE 802.1ad Q-in-Q tunneling Private VLAN Edge (PVE) MAC-based VLAN Protocol-based VLAN Voice VLAN MVR (Multicast VLAN Registration) GVRP Up to 4K VLAN groups, out of 4095 VLAN IDs |
Link Aggregation | IEEE 802.3ad LACP/static trunk Supports 3 trunk groups with 4 ports per trunk group |
Spanning Tree Protocol | IEEE 802.1D Spanning Tree Protocol IEEE 802.1w Rapid Spanning Tree Protocol IEEE 802.1s Multiple Spanning Tree Protocol |
IGMP Snooping | IPv4 IGMP (v1/v2/v3) snooping IPv4 IGMP querier mode support Supports 255 IGMP groups |
MLD Snooping | IPv6 MLD (v1/v2) snooping, IPv6 MLD querier mode support Supports 255 MLD groups |
Bandwidth Control | Per port bandwidth control Ingress: 500Kb~1000Mbps Egress: 500Kb~1000Mbps |
Ring | Supports ERPS, and complies with ITU-T G.8032 Recovery time < 10ms Supports Major ring and sub-ring |
Synchronization | IEEE 1588v2 PTP(Precision Time Protocol) Peer-to-peer transparent clock End-to-end transparent clock |
QoS | Traffic classification based, strict priority and WRR 8-level priority for switching Port number 802.1p priority 802.1Q VLAN tag DSCP/TOS field in IP packet |
Layer 3 Functions | |
IP Interfaces | Max. 128 VLAN interfaces |
Routing Table | Max. 128 routing entries |
Routing Protocols | IPv4 hardware static routing IPv6 hardware static routing RIPv2 dynamic routing IPv4 OSPFv2 dynamic routing IPv6 OSPFv3 dynamic routing |
Security Functions | |
Access Control List | IP-based ACL/MAC-based ACL ACL based on: MAC Address IP Address Ethertype Protocol Type VLAN ID DSCP 802.1p Priority Up to 256 entries |
Security | Port security IP source guard Dynamic ARP inspection Command line authority control based on user level |
AAA | RADIUS client TACACS+ client |
Network Access Control | IEEE 802.1x port-based network access control MAC-based authentication Local/RADIUS authentication |
Management Functions | |
Basic Management Interfaces | Console; Telnet; Web browser; SNMP v1, v2c |
Secure Management Interfaces | SSHv2, TLSv1.2, SNMPv3 |
System Management | Firmware upgrade by HTTP protocol through Ethernet network Configuration upload/download through HTTP Remote Syslog System log LLDP protocol NTP PLANET Smart Discovery Utility PLANET CloudViewer app |
Event Management | Remote Syslog System log SMTP |
ONVIF | ONVIF device discovery ONVIF device monitoring Floor Map |
SNMP MIBs | RFC 1213 MIB-II RFC 1493 Bridge MIB RFC 1643 Ethernet MIB RFC 2863 Interface MIB RFC 2665 Ether-Like MIB RFC 2819 RMON MIB (Group 1, 2, 3 and 9) RFC 2737 Entity MIB RFC 2618 RADIUS Client MIB RFC 2863 IF-MIB RFC 2933 IGMP-STD-MIB RFC 3411 SNMP-Frameworks-MIB RFC 4292 IP Forward MIB RFC 4293 IP MIB RFC 4836 MAU-MIB IEEE 802.1X PAE LLDP MAU-MIB Power over Ethernet MIB |
Standards Conformance | |
Regulatory Compliance | FCC Part 15 Class A CE: EN 55032 , EN 55035 EN 50121-4, EN 50121-1 EN 61000-6-2, EN 61000-6-4 |
Railway | EN50121-4 |
Stability Testing | IEC 60068-2-32 (free fall) IEC 60068-2-27 (shock) IEC 60068-2-6 (vibration) |
Standards Compliance | IEEE 802.3 10BASE-T IEEE 802.3u 100BASE-TX/100BASE-FX IEEE 802.3z Gigabit SX/LX IEEE 802.3ab Gigabit 1000T IEEE 802.3ae 10Gb/s Ethernet IEEE 802.3x flow control and back pressure IEEE 802.3ad port trunk with LACP IEEE 802.1D Spanning Tree Protocol IEEE 802.1w Rapid Spanning Tree Protocol IEEE 802.1s Multiple Spanning Tree Protocol IEEE 802.1p Class of Service IEEE 802.1Q VLAN tagging IEEE 802.1X Port Authentication Network Control IEEE 802.1ab LLDP IEEE 802.3af Power over Ethernet IEEE 802.3at Power over Ethernet Plus IEEE 802.3bt Power over Ethernet Plus Plus IEEE 802.3ah OAM IEEE 802.1ag Connectivity Fault Management (CFM) RFC 768 UDP RFC 793 TFTP RFC 791 IP RFC 792 ICMP RFC 2068 HTTP RFC 1112 IGMP v1 RFC 2236 IGMP v2 RFC 3376 IGMP v3 RFC 2710 MLD v1 RFC 3810 MLD v2 RFC 2328 OSPF v2 ITU-T G.8032 ERPS Ring ITU-T Y.1731 Performance Monitoring |
Environment | |
Operating Temperature | -40 ~ 75 degrees C |
Storage Temperature | -40 ~ 85 degrees C |
Humidity | 5 ~ 95% (non-condensing) |